17-4PH Chemistry & Specifications; ASTM F593 Grade 630 fasteners; 17-4PH Datasheet; 17-4 PH bolts are made from a precipitation hardened stainless steel most known for its exceptional strength and its ability to maintain its mechanical properties to 600°F. Compared to 316 stainless steel, 17-4 PH bolts yield strength is up over 4 times greater.
17-4 PH stainless steel can be used for a variety of industries including pump shafts, oil path, mechanical seals, and within the aerospace industry. Its composition is carbon, chromium, columbian + tantalum, copper, manganese, nickel, phosphorous, silicon, and sulfur. 17-4 PH® Stainless Steel, UNS S17400 - Ulbrich17-4 PH® is a martensitic, chromium-nickel-copperprecipitation-hardening stainless steel that provides anoutstanding combination of high strength, good corrosion resistance, good mechanicalproperties at temperatures up to 600ºF (316ºC). This alloy is typically furnished in ConditionA (annealed) but can be cold rolled to various temper ranges.
17-4 STAINLESS STEEL AMS 5643 AISI 630 UNS S17400 17-4 Stainless is a martensitic chromium-nickel-copper stainless steel in the solution treated (annealed) condition. It can be further hardened to various strength levels by a single precipitation hardening heat treatment that minimizes scaling and distortion. 17-4 Stainless Steel Bar - National Specialty Alloys17-4 stainless steel bar, also known as UNS S17400, 17-4 PH and Grade 630, is one of the original precipitation hardened grades developed in the 50s. Primarily comprised of 17% chromium, 4% nickel, 4% copper, with the balance being iron. There are also trace amounts of manganese, phosphorus, sulfur, silicon, columbium (or niobium) and tantalum.
17-4 - UNS S17400:Type 17-4 is the most common grade of martensitic precipitation hardenable (PH) alloys. 17-4 provides an outstanding combination of high strength, good mechanical properties at temperatures up to 600°F (316°C), and short-duration, low-temperature heat treatments that minimize warpage and scaling. 17-4PH Annealed - Penn StainlessOct 24, 2018 · General Properties. Alloy 17-4 is a chromium-copper precipitation hardening stainless steel that is used for applications requiring high strength and a moderate level of corrosion resistance. It is one of the most widely used precipitation hardening grades, as it has high strength hardness up to about 572°F while demonstrating good corrosion
17-4PH requires similar arc and resistance welding processes to those used on standard specifications of stainless steel. Welding up to 100mm thick can be carried out without the requirement of pre heating due to its low hardness. We recommend you contact your welding consumables supplier who should provide you full assistance and information ARMCO 17-4 PH - AK Steel5 rows · SPECIFICATIONS AK Steels ARMCO 17-4 PH Stainless Steel in bar, wire, forgings, and
17-4PH Mechanical Properties Tensile strength 231-231 b/MPa Yield Strength 154 0.2 /MPa Elongation 56 5(%) - (%) Akv - Akv/J HBS 235-268 - HRC 30 - Tel:+86-80247006 Email:[email protected] https://steel-grades/ Page 3 / 4 Heat Treatment of 17-4 PH Stainless Steel17-4 PH stainless steel is a martensitic stainless steel containing approximately 3 wt pct Cu and is strengthened by precipitation of copper in the reduction to make the properties that are required by the appropriate specification. As . PH
View our full selection of 0.1" Stainless Sheet 17-4 PH Cond. A stock today on our website. Buy online with fast shipping direct to your door. P R O D U C T D A T A S H E E T 17-4 PH STEEL STAINLESSAK Steel 17-4 PH Stainless Steel is well known in reference literature and more information can be obtained in this way. SPECIFICATIONS Specifications are listed without revision indications. Contact ASTM Headquarters for latest ASTM revision. For AMS revi-sion, contact AMS Division of SAE. AMS 5604 Sheet, Strip and Plate ASTM A 693 Plate
15-5 PH Stainless Steel . Specification:AMS 5862, AMS 5659, AMS 5826, ASTM A 564, ASTM SA 564, ASTM A 693,ASME SA 693, ASTM A 705, ASME SA 705 15-5PH Precipitation Hardening Stainless Steel Alloy (S15500) is a variant of the older 17-4 PH (S17400) chromium-nickel-copper precipitation hardening stainless steel. Stainless Steel 17-7Ph (AMS 5528 / AMS 5529 / AMS 5644 17-7PH Foil (Shim) is available in various thicknesses. View stock list for further information. Foil Stock List, Sheet Stock List, Plate Stock List. or contact Sales. Specifications Type 17-7 PH Stainless Steel is covered by the following specifications:AMS 5528 Sheet, Strip and Plate AMS 5529 Sheet, Strip Cold Rolled AMS 5568 Welded Tubing
stainless steel 1.4571 equivalent, stainless steel 1.4408 equivalent, stainless steel 1.4301 equivalent, stainless steel 1.4541 equivalent, stainless steel 1.4310 equivalent, stainless steel 1.4462 equivalent, stainless steel 310 equivalent, stainless steel aisi 316l equivalent, stainless steel aisi 316 equivalent What is the difference between 17-4 and 316L stainless steel?17-4 Stainless Steel. 17-4 stainless steel, also known as SAE Type 630, is a common and exceptionally durable type of steel used in a diverse variety of industries and applications. The numbers 17-4 refer to its composition:17% chromium and 4% nickel. It
Stainless Steel 17-4 Product Guide. Applications Stainless 17-4 Specifications Mechanical and Chemical Data. Overview. 17-4 stainless has high tensile strength and hardness and excellent corrosion resistance up to high temperatures. It is typically used in gate valves, chemical processing equipment, pump shafts, gears, ball bearings Stainless Steel AL 17-4 PrecipitationStainless Steel AL 17-4 Alloy SUMMARY OF HEAT TREATING AL 17-4 ALLOY Minimum Properties Specified in Aerospace Material Specification (AMS) 5604 Heat Treat to Produce Martensitic Structure Precipitation Heat Treatment to Produce Desired Strength Solution Heat Treatment at 1950 °F (1066 °C) Precipitation Hardening Heat Treatment 900 °F (482 °C) 60 minutes